Nitrates, Arsenic, and Private Wells: When Test Kits Are Not Enough

Why private wells need lab-based decisions for nitrates, arsenic, bacteria, local geology, flooding, and treatment design.

A rural well visible through a window with water storage containers, sample bottles, filter cartridges, and notes on a utility table.
On this page

Private well owners are responsible for testing their water and deciding what to do with the results. Nitrate and arsenic can be present in clear, pleasant-tasting water, and a general-purpose filter does not necessarily remove either one. A certified laboratory and local health department can help you turn a result into a plan for your particular well.

Heads up
Water safety boundary

Clear Water Lab helps with everyday water decisions, reports, testing, certification checks, and maintenance. It is not medical advice, legal advice, or a substitute for local boil-water notices, certified lab results, utility instructions, or health department guidance.

When to use another water source

If a test shows nitrate above the applicable health guidance, or arsenic at a concerning level, use bottled water or another source known to be safe for drinking, cooking, and preparing infant formula while you contact your health department. Do not wait for a confirmation sample before reducing exposure. Ask the department whether other uses need precautions and when to retest.

High nitrate is especially dangerous for infants: it can interfere with the blood’s ability to carry oxygen. Bottle-fed babies under six months are particularly vulnerable. If an infant has bluish skin or trouble breathing, seek emergency medical care. Do not use untested well water to prepare formula; test it first and discuss a safe source with the child’s healthcare provider. Minnesota’s health department recommends an alternative for infants under six months when the well exceeds its nitrate limit, even if a nitrate treatment device is installed, because a device can fail without an obvious warning. See its nitrate guidance .

Boiling does not remove nitrate or arsenic and can concentrate them as water evaporates. If bacteria are also a concern, ask the health department for a safe alternative rather than assuming boiling solves both problems. Distillation is different: a distiller collects and condenses steam instead of leaving the water in the pot.

Why these contaminants need separate tests

Nitrate can reach groundwater from fertilizer, septic systems, animal waste, and other sources. Its level can change with conditions such as rainfall and land use. A high result can also be a reason to ask about other contaminants, including bacteria, but does not identify the source by itself. CDC’s well testing guide explains common sources and testing triggers.

Arsenic can occur naturally in rock and soil, as well as from some human activities. Long-term exposure in drinking water increases the risk of cancer and other health problems. Levels can differ between nearby wells, so a neighbor’s result cannot establish yours. Minnesota’s arsenic guide explains the health risks and treatment options.

Neither a pleasant taste nor a clear sample rules out nitrate or arsenic. A store test may provide an initial clue, but use a laboratory certified for the specific drinking-water analyses when making health and treatment decisions. Total dissolved solids and pH measurements do not tell you the concentration of either contaminant.

Choose a test and collect the sample

  1. Ask about the local panel. CDC recommends testing a private well at least yearly for total coliform bacteria, nitrate, total dissolved solids, and pH. Ask your local health or environmental department whether arsenic, pesticides, other chemicals, or additional germs are concerns in your area and how often to test for them. Arsenic is not necessarily included in a routine panel. Minnesota recommends testing every well for arsenic at least once; local recommendations may differ. If a baby will use the water, also ask which other tests are appropriate, including manganese.
  2. Find a certified lab. Ask the department or consult EPA’s state laboratory certification contacts . Confirm that the lab is certified for the particular tests, ask about cost and turnaround, and request bottles and instructions. Ask whether its reporting limits are low enough to compare with the guidance you plan to use.
  3. Identify the sampling point. Ask the lab how to sample untreated water to characterize the well and, if treatment is installed, the drinking tap to assess what you consume. Label each sample clearly; a treated tap alone cannot show the untreated well concentration. Follow the lab’s instructions for the tap, flushing, bottles, handling, and delivery deadlines. The home sampling guide is a useful preparation, but the lab’s protocol takes priority.
  4. Keep the report. Record the date, tap, whether water was treated, recent rainfall or flooding, and any well or plumbing work. Ask the lab about a result marked “not detected”: it means the concentration was below that lab’s reporting limit, not necessarily zero. If that limit is above a level you need to assess, the result cannot tell you whether the water is below that level. See lab result units and detection limits .

Test again after flooding, well repairs, a significant change near the well, or a change in taste, color, or odor. CDC also recommends testing when someone becomes pregnant or a child starts living in the home. Ask about additional timing if past nitrate results fluctuate or local conditions change. For a new well, ask when an arsenic retest would be useful: Minnesota notes that results can change during the first months after construction. For a property purchase, obtain current results for the well and the contaminants relevant to the site rather than relying on taste or old paperwork.

Read the numbers carefully

The following U.S. federal maximum contaminant levels apply to regulated public water systems, not as enforceable limits for an individual private well. They are useful reference points to discuss with your health department; local guidance may be more protective.

ResultReference point and next step
NitrateThe federal limit is 10 mg/L as nitrogen, approximately 44 mg/L as nitrate. Check how the lab expresses the result before comparing: 10 mg/L as nitrate is not the same as 10 mg/L as nitrogen. If the result is above the applicable guidance, use a safe alternative and contact the health department. Ask about follow-up testing and inspection of the well and potential sources.
ArsenicThe federal limit is 10 µg/L, also written as 10 ppb or 0.010 mg/L. The federal health goal is zero; a result below the regulatory limit does not mean there is no long-term risk. Discuss any detection and local guidance with the health department, including whether a confirmation sample is appropriate.

The nitrate conversion and reference level are described in EPA’s nitrate material ; Minnesota’s arsenic guide explains the arsenic limit and health goal. For example, a report of 8 mg/L as nitrate is equivalent to about 1.8 mg/L as nitrogen, not 8 mg/L as nitrogen. Both reporting bases describe nitrate concentration, but the numerical values differ. If a report says “nitrate plus nitrite” or uses an unfamiliar unit, ask the lab or health department to interpret that specific result rather than applying the nitrate number mechanically. A single sample describes the water at that time and place; it is not a guarantee for every season or every tap.

Choose treatment from the results

Start with the full lab report and the water uses that need protection. A carbon filter for taste is not automatically a nitrate or arsenic treatment, and a conventional water softener is not a nitrate or arsenic solution. Reverse osmosis may reduce both contaminants; distillation, appropriate ion exchange, or arsenic-specific media may also be options depending on the water and system. No one device addresses every contaminant. Arsenic can occur in different forms that affect treatment performance. In particular, arsenic III can be harder to remove than arsenic V; ask a qualified professional whether testing for these forms or pretreatment is needed before choosing equipment. Research on private-well treatment illustrates why the form and the untreated concentration matter.

For any device, check independent certification for the specific contaminant reduction on the exact system and replacement components, along with the incoming-water conditions, capacity, and maintenance requirements. A certification standard number or an advertising claim alone is not enough. Ask how the system handles waste water or spent media and whether pretreatment is needed. How to Verify a Water Filter Claim and Reverse Osmosis for Beginners explain the checks.

After installation, use a known safe alternative until a lab test confirms the treated water meets the applicable guidance. Arrange testing at the treated drinking tap with the lab or health department, then agree on a retesting schedule; a separate untreated sample helps show what the system is receiving. Keep both reports, installation details, and cartridge or media replacement dates together. If the system serves only one tap, use that tap for drinking and cooking; check whether the refrigerator and ice maker are connected to it or need a separate safe supply. A different source, a well repair, or a new well may also be worth discussing locally; a new well does not guarantee better water without testing.

Bacteria require their own response. UV or disinfection may be appropriate for some microbiological problems, but neither is a nitrate or arsenic removal plan. After a flood, follow local instructions before returning the well to service; see Private Well After Flooding and Private Well Coliform and E. coli Results .

Try this next

  • Ask the local health department which tests and retesting intervals fit your well and household.
  • Order nitrate, arsenic, and the locally recommended panel from a certified lab; follow its collection and delivery instructions.
  • Compare the report using the correct units and contact the health department about results or an appropriate alternative water source.
  • Keep reports, well repairs, treatment manuals, and maintenance dates together in a well water sampling log .

Official references

Sources & further reading

Written By

JJ Ben-Joseph

Founder and CEO · TensorSpace

Founder and CEO of TensorSpace and the editor of Fondsites: an engineer working across software, AI, cybersecurity, and biosecurity who builds the site's games and tools.

Keep reading